Amp hook up to factory radio, adding subwoofer to stock car radio polk audio

Make sure the control wire from your deck to the amp is connected. Hi Buck its Josh again, thankyou for your help thus far. After identifying the speaker wires, you cut each one and connect the end coming from the radio's output to the amp's input, and the end going to the car speakers to the amp's output. Give us a call at and an Advisor will help you get what you need.

An online search ought to bring up at least one car stereo dealership somewhere near you. You'll also need a crossover filter, high-pass, to prevent bass notes tearing the tweeters apart. Every amp has pre-drilled mounting screw holes located on each of the four corners of the amp for easier mounting. Tracy, giochi speed A capacitor provides a jolt of power to an electrical system when the demand exceeds the normal supply. When do you want us to call you back?

While your key and radio is on, disconnect and connect the remote wire to the amp. Warnings Be careful when around the electrical system of your car. Paint the hole's edges to protect against rust.

Adding subwoofer to stock car radio Polk Audio

If you want advice or a question answered about a system, you must identify all the equipment by brand names and model numbers. Reconnect your car battery, and test your new audio system. Run the wire under the carpet by removing the rocker panel and kick panel covers. Or would my sub have to share the same full sound as the speakers are receiving? Dan, A relay to control the turn-on circuit of a system doesn't become necessary until there are about three or more devices on that circuit.

How to Wire an Amp & Subwoofers Into a Stock Stereo

Turn up the deck's volume until you hear distortion, and set it just below that level. Make sure to connect positive to positive and negative to negative. Any suggestions or will my factory electrical system withstand that? How would I wire from my factory radio to the amp if it doesn't have those outputs? That's why we went with the standard system.

Factory Harley Radio Integration Secrets for 14 & Up

Wiring Subwoofers to stock Radio Interior

Guide to Car Speakers

Just figured I'd ask about certain things. If you bought your amp from Crutchfield, dating a single dad long you could call Tech Support for free help troubleshooting your system. Choose a subwoofer speaker system and amplifier that fits your car's current system and meets your audio needs.

Re Wiring Subwoofers to stock Radio

Dodge Avenger Forum

My issue is I want to add onto that with an additional amp and sub. The diagram gives a generalized picture of how it connects. Power on your car and stereo system and test your subwoofer for output. They should be there for additional protection. Generally, the positive wire will be red and the negative will be black.

And why do I need to use a ground block? Amplifier wiring diagrams How to add an amplifier to your car audio system. What would happen if you hooked it up and the subs blew? Installing an amp can be done without the help of a professional, allowing you to get great sound without an installation fee. Figure out where you're going to place the amp, put the beginning of your power red wire there and give it about a foot of wire extra, then begin to hide and run the power wire to under the hood.

If you don't already have one, purchase a car amplifier with speaker-level inputs and also purchase an amp installation kit. Both of these amps equal amp, so i have a amp breaker at the battery. Please keep your phone line open. If you're using the amp for a subwoofer, internet dating rsa use the rear channels of the receiver and go through the receiver's menu to see if there are subwoofer settings you need to adjust.

How should I connect the remote wire so that I don't have to disconnect it when I turn off the car? Safe as in not damaging the amp or sub. It is best to install it as close as possible to the connection. From the block outputs routed the wire to each amp.

Factory radio to amp

Related articles Car amplifier buying guide. Most amplifiers will have outputs for at least two speakers. Ameer, early dating scan uk We're only licensed to sell gear in the United States and Canada. Our day money-back guarantee. Don't forget to fuse each cable near the battery.

What Are Some Alarms for an Expensive Audio System
Quick Links

You can certainly add a powered sub to the system to improve the bass if the factory subwoofer amp isn't powerful enough for you. Mount the antenna to the truck and run the coax to the radio following a path that does not cause interference with other functions like seat adjustment or the pedals. Can I still add the sub to the stock radio? Yes, it means that I have to run cables from receiver to the amp, and then from amp back to the receiver area where main wiring harness is.

Richard, Call Crutchfield Tech Support for help. Remote connections, via a receiver's port or a vehicle fuse box, turn on and off with the car's ignition and can work with more than one amplifier. Any volume discrepancy between front and rear speakers can be balanced using the amp's gain or the receiver's fade control. Hey buck, I'll list my equipment first, then what I'm trying to do. We have encountered a problem.

It Still Works

Now that your amp is tapped into your car's factory audio system, run speaker wires from the amp's speaker outputs to the speaker s or sub-woofer s you want the amp to power. If you want a question answered about a system, you must identify the gear by brand names and model numbers so we can get the right information to you. You show the positive connection from the battery, and the components grounding to the chassis. How do you hook up a amp to a stock radio in a jeep Grnd Cherokee? The rest of the active was an excellent read though.

What the DSR1 Lacks

Josh, Fuses blow for a number of reasons, including being in-circuit during amplifier installation where a sudden jolt of current occurs when the amp gets connected. Start with a pilot hole and then work your way up to a size that will fit your wire. How do you hook up subwoofers to an stock radio? Seems a lot easier than pulling everything out again.

Dana, It sounds to me like everything you have is hooked up just fine and safely. How do you hook up your amp to your factory radio? Can you hook a ipod up to a car radio? And what's the point of wiring the factory speaker wires into the wiring harness for the head unit?

Hello Buck, I have a question regarding relays. Give them a call and they can help you with your install. This article is intended to be an aid to anyone looking to upgrade their Harley audio system with the new generation of radio. It will just plug into your truck and then connect color coordinated wires.

Hooking up a amp to the factory radio
  • The motor that raises and lowers the antenna is controlled by a wire which is connected to the power switch in the stock radio.
  • Could you please help with a description.
  • Run your amp wires battery, ground.
  • All products are possible, so the recommendations would still be appreciated.
Factory Harley Radio Integration Secrets for 14 & Up

Electrically, it'll be connected to all the amps in your system, but it will do the most good to the nearest amp. The model number and impedances are marked by the wiring terminals. Joe, You most certainly can put together a system as you describe, but running an active audio system is a lot more complex than a passive one.

  1. The speed controlled volume feature increases volume of the radio as your speed increases.
  2. Ground goes directly to chassis - you don't need a ground block.
  3. What should I do if I want to play all my speakers through the amplifier?
  • Dating separated dad
  • Rules online dating texting
  • Marriage not dating ep 14
  • The most popular dating sites in france
  • Dating a shy quiet guy
  • Dating a team magma grunt chapter 1
  • Legal age of dating
  • Indian online dating app